Teilenummer
Entmilitarisierung
Lagerfähigkeit
UOM
NIIN
NSN
Nationale Bestandsnummer:
TXT
Beschreibung:
Engine Accessory Generator
MRC:
The direction of the thread when viewed axially. a right-hand thread winds in a clockwise direction while a left-hand thread winds in a counterclockwise direction.AAJF
Thread Direction:
Right-hand
MRC:
A measurement of the extent of threads,including incomplete threads,along a line parallel to the longitudinal axis.AASA
Thread Length:
0.844 inches
MRC:
The length of a straight line which passes through the center of the smallest cross section of a spline,and terminates at the circumference.AAUH
Spline Minor Diameter:
Any acceptable
MRC:
The length of a straight line which passes through the center of the largest cross section of a spline,and terminates at the circumference.AAUJ
Spline Major Diameter:
0.874 inches
Spline Width:
Between 0.216 inches and 0.217 inches
MRC:
The number of splines on or in the item.ABSA
Spline Quantity:
6
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the mounting.ADER
Mounting Style:
Bracket mtd w/three mtg holes
MRC:
The environmental elements or conditions that an item is designed or protected to resist or withstand satisfactorily.ADZC
Environmental Protection:
Corrosion resistant and fungus resistant
MRC:
An indication of whether or not an item is capable of operation while submerged.AHZV
Submersibility:
Nonsubmersible
MRC:
The maximum altitude at which the item is rated to function.AKAE
Maximum Operating Altitude Rating:
Not rated
MRC:
The direction of rotation of a rotating shaft as viewed from the drive end.AKCT
Shaft Rotation Direction:
Clockwise
MRC:
The length of a straight line which passes through the center of the threaded portion,and terminates at the circumference.AWDP
Thread Diameter:
0.625 inches
MRC:
A measurement of the longest dimension of a spline,in distinction from width.AXFH
Spline Length:
2.000 inches
MRC:
The minimum speed the armature can revolve and maintain full current output,expressed in revolutions per minute.BCGD
Armature Minimum Speed In Rpm At Full Current Output:
900
MRC:
The maximum amount of output current for which the item is rated,expressed in amperes.BCGF
Maximum Output Current Rating In Amps:
55.0
MRC:
The cut-in speed necessary to maintain a minimum current flow,expressed in revolutions per minute.BCGG
Minimum Current Cut-in Speed In Rpm:
580
MRC:
The means by which the item is grounded.BCGN
Grounding Method:
Internal
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the shaft drive end.BCGS
Shaft Drive End Style:
Splined shaft end, threaded
Distance Between Shaft Center And Bottom Mounting Hole Center:
4.500 inches
Distance Between Shaft Center And Top Mounting Hole Center:
4.875 inches
Angular Deviation Of First Hole From Top Center In Deg:
170.0
Angular Deviation Of Second Hole From First Hole In Deg:
190.0
Distance Between Inside Surfaces Of Hinge Bracket:
4.250 inches
Distance Between Outside Surfaces Of Hinge Bracket:
Between 5.370 inches and 5.380 inches
Top Mounting Hole Diameter:
0.531 inches
Bottom Mounting Hole Diameter:
Between 0.627 inches and 0.629 inches
MRC:
The speed the armature can revolve and produce maximum current,expressed in revolutions per minute.BCND
Maximum Rated Armature Speed In Rpm:
3600
MRC:
A designation indicating the diameter-pitch combination and the number of threads per measurement scale applied to a series of diameters.BZRR
Thread Series:
Unf
MRC:
A numeric-alpha designator indicating the pitch-diameter tolerance and the external or internal location of the thread.CFHL
Thread Class:
2a
MRC:
The number of threads on the item per linear inch measured on a line parallel to the thread axis.CMLP
Thready Qty Per Inch (tpi):
18
MRC:
The total electrical voltage.ELEC
Voltage In Volts:
12.0
